mirror of
https://github.com/legop3/MultiRoombaRover.git
synced 2026-11-17 04:02:21 -05:00
cleanups
This commit is contained in:
@@ -45,7 +45,7 @@ The parent switch now defaults to disabled. Saved child settings do not enable G
|
||||
- [x] Add AIY capture/playback profiles alongside generic selectable ALSA device profiles.
|
||||
- [x] Make TTS, horn, forwarded audio, and mixer routing use configured devices consistently.
|
||||
- [x] Generate ALSA routing from the shared input/output configuration, including distinct input/output cards, logical profile devices, format conversion, and independent playback volume controls.
|
||||
- [ ] Audit fixed card numbers, named PCM assumptions, capture formats, camera orientation/sensor defaults, serial device defaults, and architecture-specific TTS assets.
|
||||
- [x] Audit fixed card numbers, named PCM assumptions, capture formats, camera orientation/sensor defaults, serial device defaults, and architecture-specific TTS assets. Findings and deployment checks are below.
|
||||
- [x] Keep required one-time host boot changes visible; distinguish a hardware-overlay reboot from ordinary roverd update/restart behavior.
|
||||
- [x] Add exact final profile selections and JSON settings for the existing AIY rover.
|
||||
- [ ] Verify on the actual HAT and at least one non-HAT audio device; record results rather than assuming compatibility.
|
||||
@@ -65,3 +65,16 @@ For the existing AIY v1 setup, start with these fields in a complete current con
|
||||
- Enable the parent `piGpio.enabled` and the desired child roles as described above. The old automatic PWM-overlay installer is gone; the GPIO12/13 PWM overlay remains a documented host wiring requirement, not an audio-profile side effect.
|
||||
|
||||
The HAT setup does not disable unrelated onboard audio or force a card index. Use the configured stable device/card names. Existing installed media systemd units must be removed/disabled before running the new supervisor. Remove any old roverd-specific host ALSA configuration before deployment: the generated config includes the system ALSA definitions, whose hooks can still load host configuration. The old media launchers are no longer used.
|
||||
|
||||
|
||||
## Hardware assumption audit (2026-11-16)
|
||||
|
||||
- New configs use a non-inverted camera and automatic CSI sensor mode (empty `media.video.sensorMode`). The AIY/CSI sample and checked-in rover config retain the existing inverted mount and `1296:972` selection. For your existing rover set `media.video.inverted` to true and retain that sensor mode only if supported by the connected camera. V4L2 uses `media.video.device` and `inputFormat`; its profile ignores the CSI mode.
|
||||
- `serial.device` defaults to `/dev/ttyUSB0`, but accepts a stable `/dev/serial/by-id/...` path. Select the Roomba adapter explicitly to avoid depending on USB enumeration. Peripheral discovery excludes that device.
|
||||
- Audio card zero and 48 kHz stereo are editable defaults, not mandatory hardware. Set the physical input/output separately and use the HAT's 16 kHz mono output values above. Logical plug devices perform format conversion; the physical output still needs to support the chosen dmix format. Verify microphone channels/rate against actual hardware.
|
||||
- Chrome TTS assets are chosen by installed OS architecture; ARMv6 has no bundled Chrome library and should use `audio.defaultEngine: "flite"` or `"espeak"`. Chrome libraries/voices still require on-device verification. TTS, horn, and forwarded audio use the generated routing; verify independent gains after each logical PCM has opened, when ALSA creates its soft-volume control.
|
||||
- Pi firmware voltage/throttle probes run only when `vcgencmd` is installed. Native GPIO access remains controlled by `piGpio.enabled`, independently of host-health telemetry.
|
||||
- AIY profile setup adds new boot settings under `[all]`. If existing matching settings are inside a model-specific section, ensure that section applies to your Pi. The profile does not rewrite existing host sections.
|
||||
- Keep `dtoverlay=pwm-2chan,pin=12,func=4,pin2=13,func2=4` in an applicable boot-config section for the existing GPIO12 servo wiring. Keep GPIO18/19 free for the HAT's I2S. Reboot after overlay changes.
|
||||
|
||||
No camera, ALSA device, firmware command, or GPIO operation was exercised during this source audit. Host installation, browser flows, and physical hardware verification remain required.
|
||||
|
||||
Reference in New Issue
Block a user